Classic Elegance

Requirements

• 1 pack Ribtex Glass Bi-cones 4mm Black (GB203)
• 1 pack Ribtex Glass Cubes 8mm Black (CUB303)
• 1 pack Ribtex Glass Pearls 10mm White (GPL404)   
• 6 packs Ribtex Jewellery Bitz Diamante Rondel 6mm (JF211)
• 2 packs Ribtex Jewellery Bitz Eye Pins Silver (JF150) 
• 1 pack Ribtex Jewellery Bitz Head Pins Silver (JF183)
• 1 pack Ribtex Jewellery Bitz Jump Rings Small Silver (JF114)
• 1 pack Ribtex Jewellery Bitz Heart Berry Toggle Silver (JF203)
• 1 pack Ribtex Jewellery Bitz Shepherd Hooks Silver (JF110)  
• Access to Ribtex Jewellery Bitz Cutter Pliers (JF165)
• Access to Ribtex Jewellery Bitz Round Nose Pliers (JF166) 

Instructions

Assemble Components

1.  Cube Head Pin - Thread 1 x rondel, 1 x glass cube and 1 x rondel onto a Head Pin.  Leaving approximately 1cm, trim excess wire and form a loop at the end of the pin with round nose pliers.  Make 1.

2.  Cube Eye Pins  - Thread 1 x rondel, 1 x glass cube and 1 x rondel onto an Eye Pin.  Leaving approximately 1cm, trim excess wire and form a loop at the end of the pin with round nose pliers.  Make 8.

3.  Pearl Eye Pins - Thread 1 x glass bi-cone, 1 x glass pearl, 1 x glass bi-cone onto an Eye Pin.  Leaving approximately 1cm, trim excess wire and form a loop at the end of the pin with round nose pliers.  Make 9.

Centre Feature

4.  Connect Cube Head Pin (from step 1) to Pearl Eye Pin (from step 3) by gently opening the loop of the head pin and hooking the eye pin loop into it.

5.  Interlock two sets of 2 jump rings together and place the last jump ring into the loop at either end of a Cube Eye Pin (from step 2).

6.  Connect the eye pin loops from step 4 and step 5.  Connect the second jump ring loop to the toggle bar as shown.

Constructing the Necklace

7.  Begin the sequence from the two remaining interlocked jump rings on the centre feature.

8.  Loop into the top jump ring 1 x Pearl Eye Pin, then into that eye pin loop 1 x Cube Eye Pin, then 1 x Pearl Eye Pin into the previous eye pin loop.  Continue until you have used all of your eye pins.  You can vary the length of your necklace to suit by adding or removing eye pins.

9.  Connect the final Pearl Eye Pin to the Heart Toggle with a jump ring.

10.  Interlock the toggle bar into the jump ring and your necklace is complete.

Earrings to match

Thread 1 x Glass Pearl, 1 x rondel, 1 x glass cube onto a head pin, leave approximately 1 cm and trim excess wire and form a loop at the end of the pin with round nose pliers and attach to shepherd hook.  Close loop.

Earrings Three Tiered

Items used as per example Glass Pearls Barely Pink 10mm (GPL402), Glass Pearls Barely Pink 8mm (GPL302), Glass Pearls Barley Pink 6mm (GPL202), Bead Cap (CHM207), Diamante Rondels (JF211), Head Pins Silver (JF183) and Shepherd Hooks (JF110).

Thread 10mm Glass Pearl, Rondel, 8,, Glass Pearl, Bead Cap and 6mm Glass Pearl onto a head pin.  Leave approximately 1cm and trim excess wire and form a loop at the end of the pin with round nose pliers and attach to shepherd hook.

Links and Downloads

Classic Elegance PDF Download 290kb. Download...